Categories
>Size: 88X50X31mm (including installation hole 96.5X50X31mm)
>Voltage and current: 9~15V100mA
>Relay maximum load: AC250V10A, DC30V10A
Brand:
S4AItem NO.:
Wiegand-DryWiegand output to relay dry point
Model No.: Wiegand-Dry
Wiegand switch module
Instructions for use
All-in-one access control machines, face recognition machines, and fingerprint machines sold on the market have built-in relays to control the door lock switch. Since the devices are installed outside the door, they are easy to be damaged and short-circuited to open the door, posing potential safety hazards. This device can be installed in a safe place inside the door to isolate the access control identification device and the electric lock, and use the Wiegand output of the access control identification device to control the unlocking to improve the security of access control.
Size | 88X50X31mm (including installation hole 96.5X50X31mm) |
Voltage and current | 9~15V100mA |
Relay maximum load | AC250V10A, DC30V10A |
Relay delay | minimum 1 second, maximum 60 seconds |
Wiegand interface format | WG26~WG80 |
Manual switch input | 1 channel (DR/GND), which can be connected to the door open button or dry contact signal |
Unlocking rules | any Wiegand signal is fine |
Set relay action hold time
(When setting, the module needs to be powered on and disconnect the card reader and relay interface)
***Short DR and GND first and keep shorted during setup***
1. The module relay action hold time defaults to 0.5~1s
2. Short-circuit D0 and GND for about 2 seconds, wait until the relay acts, and add a 10.5-second delay
Example: The relay action needs to be kept for 3 seconds, short-circuit DO and GND for 5 seconds, and then disconnect after hearing the relay action for 5 times, the setting is automatically saved and takes effect
3. Short-circuit D1 and GND for about 3 seconds, and the relay will act--the default hold time will be restored after being pressed
4. After the setting is completed, disconnect DR and GND to make the converter enter the working state
S4A Datesheet_Wiegand Output To Relay Dry Point
> Dimensions: 69x60x15mm> Operating temp: 5A/24V> Material: High quality elements with superb design> Suitable for Door: Fail-safe electric locks with signal output> Output Capability: Applied to double-door interlocking
> Dimensions: 36x34x20mm> Material: High quality elements with superb design> Suitable for Door: Externally-connected electronic lock of access controller> Output Capability: Dry contact output> Max. overload: 10A/250VAC 10A/30VDC
> Dimensions: 40x27x12mm> Input: 12-28VDC (Blue)> Output: 12VDC/1A (Green)
>Working Voltage: DC12V>Working Current: 40MA>Unlock Delay: 5-30 seconds
>Wiegand interface format:WG26~WG80>Voltage and current:5~24V30mA
> Card Type: EM Card> Metal case, anti-vandal> Digital backlit touch keypad> Multi-function standalone access controller and reader,> WG interface: WG26 Input / output> Capacity: 2000 cards / codes
Access Controller for Enhanced Alarm OutputModel No.: ACB-EA05ACB-EA05 Enhanced Alarm Output and Integrated Fire Control Expansion ControllerFire alarm output and the expansion of the joint boardI. OverviewACB-EA05 Fire alarm output and the expansion of the joint board，it is one of the access controller add-on modules，with the software settings, mainly used to provide fire and alarm signal output of the joint. The module has a practical, simple interface, the design performance characteristics of stability. With its power and relay instructions, may direct communication failures, is a good cost performance of the joint extension.II. The characteristics of modulei. Four-alarm output, free to the host controller to the definition of a door and the door to a number of features.ii. Can connect the output signal fire, the Fire received the signal controller automatically open their doors to all and have a fire alarm records available for consultation.iii. Support for the 'illegal intrusion' and 'the door is not closed for a long time' and 'coercion to enter,' and 'linkage to open the door' and 'invalid card' and 'fire' alarm linkage output, and so on.iv. Can be set for each output of the delay time 0-6000 seconds. Model No.ACB-EA05Product NameEnhanced Alarm Output and Integrated Fire Control Expansion PanelBasic InfoUnit Packing WayBrown boxAccessoriesUser Manual, warranty card, necessary parts for connecting panelFunction IntroductionApplicable to access controllerACB-R01, ACB-R02, ACB-R04, ACB-T01, ACB-T02, ACB-T04, ACB-001,ACB-002, ACB-004.Can Controlinvalid break-in alarm, long time unlocking alarm, intimidation break-in alarm, unlocking linkage output, invalid card swiping alarm, integrated fire control alarmShould pay attention toThis enhanced Alarm Output and Integrated Fire Control Expansion Panel only can compete with the ACB series controller, and the software be V6.6 or higher version.Output and input1-way input and 4-way alarm output, You can specify which function to which door of the controlled area, Can connect the fire control output, when the fire signal received, doors in the controlled area will be open automatically, and five-alarm will be recorded.OtherAllow changing anti-intimidation passwordCan set a long time unlocking alarm time: 0-6000 secondsCan set the time delay of each output from 0 to 6000
> Built in LED and Lock sensor> Voltage: DC12V and DC24V(adjustable)> Holding Force: 380KG(800Lbs)
S4A appreciate any of your inquiries and sincerelyhope to enjoy a fruitful long-term business relationship with youto share in the mutual benefits, If you have any questions, please feel free to contact us.
IPv6 network supported
English
français
Deutsch
русский
italiano
español
português
العربية
Türkçe
Tiếng Việt
Indonesia
